重载屋盖下大跨度连续预应力钢桁架设计研究

以某大跨度、重荷载屋盖工业厂房为例,提出大跨度连续预应力钢桁架的结构体系,根据厂房屋盖轻钢别墅永久荷载布置特点,分别对单榀连续钢桁架无预应力、下弦杆全长施加预应力、局部施加预应力3种状态及不同预应力度下的局部预应力钢桁架进行杆件内力对比分析,结果表明局部预应力技术能有效降低杆件内力峰值,使结构的内力分布更加合理.对相同承载力控制指标下2种预应力体系及非预应力体系的厂房整体结构进行静力分析,结果表明局部预应力结构体系能满足规范要求且更加经济.     

Constructing magnetically recoverable CdS/CaFe2O4 P–N heterojunctions for enhanced photoelectrochemical properties towards H2 evolution reaction

A novel CdS/CaFe₂O₄ (CS/CFO) heterogeneous p-n junction was created by thermal deposition of CaFe₂O₄ nanoparticles on CdS rods. The CS/CFO hetero-structured photocatalysts exhibited increasingly efficient visible light harvesting compared to the bare CdS. The CS/CFO composites also presented higher photocurrent and slower decay of photoluminescence, suggesting a better separation of the photo-generated electrons and holes. The photocatalytic H₂ evolution quantity on the optimized CS/CFO composite from water in the presence of ethanol was up to 2200 μmol after 3-h visible light illumination, which is more than twice that of the pristine CdS. The chemical interaction between CdS and CaFe₂O₄ was confirmed by the shifts in the XPS peaks, which made it possible for the charge carriers to transfer across the p-n junction interface. This research highlights the importance of forming an interfacial p-n heterojunction between two semiconductors for efficient charge separation and improved photocatalytic performance.     

M- S-H formation in MgO-SiO2slurries via wet milling for magnesia based castables

It is believed that the formation of hydration phase, MgO-SiO₂-H₂O (M-S-H), contributes to good workability and reliable comprehensive properties for magnesia based castables. In order to stimulate the formation of M-S-H in magnesia based castables and understand the minimum introduction of microslica amount, wet milling process was used to promote the dissolution of MgO and SiO₂ in this work. The slurry containing different content of microsilica with wet milling technology and the castables with/without wet milling slurry were prepared. The effects of microsilica content on the formation of hydration phases were analyzed by XRD, FT-IR and TG/DSC and the properties of magnesia based castables were evaluated by explosion resistance, CMOR, HMOR and so on. The results showed that the formation of M-S-H was accelerated because of the dissolution of Mg²⁺ and HSiO₃^? in wet milling process. Higher amount of M-S-H led to a tight bonding in the early stage, and a denser structure after firing at high temperature due to the limited formation of brucite and in-situ formation of evenly distributed forsterite phase. In addition, much higher HMOR were obtained when less microsilica was added, attributing to the suppressed formation of low-melting-point liquid. Therefore, 2–3 wt% microsilica addition was recommended in this process.     

次氯酸钠对德尔卑沙门氏菌生物被膜的抑制作用及机制

目的：为控制德尔卑沙门氏菌（Salmonella Derby）在食品加工过程中的污染，研究不同体积分数次氯酸钠对S. Derby生物被膜的抑制作用及其机制。方法：采用结晶紫染色法和平板菌落计数法观察次氯酸钠对生物被膜的抑制和清除效果，进一步观察不同体积分数次氯酸钠作用下沙门氏菌泳动能力和生物被膜内细胞的代谢活性、胞外聚合物含量和微观形态的变化规律。结果：次氯酸钠的最小抑菌浓度（minimum inhibitory concentration，MIC）为0.08%（体积分数，下同），亚MIC（0.04%、0.02%、0.01%）的次氯酸钠可以抑制S. Derby生物被膜的形成，对成熟生物被膜也有一定的清除效果，且不同亚MIC次氯酸钠的作用效果差异显著（P＜0.05）；不同体积分数次氯酸钠处理能降低生物被膜内细胞代谢活性，抑制胞外多糖的合成，且不同体积分数次氯酸钠的作用效果差异显著（P＜0.05）。激光共聚焦扫描显微镜结果显示，与对照组相比，次氯酸钠处理使得生物被膜厚度减小、活菌数减少、死菌数增多、细菌由聚集状态变为分散状态。结论：不同体积分数次氯酸钠对S. Derby生物被膜的形成有明显的抑制作用，这一作用与干扰细菌生长、生物被膜内细胞代谢活性和胞外多糖的合成有关。     

老旧塑胶运动场改造工程案例研究

以江苏师范大学400 m标准塑胶运动场改造工程为例,重点介绍了塑胶打磨工艺的施工流程、特点及发展方向,分析了塑胶打磨工艺,在保证施工质量的同时,可降低11.2％的工程造价.最后提出打磨工艺的施工要点、适用情况及塑胶运动场的建设和改造建议,相关的经验可供类似工程借鉴.     

一种起重机控制柜温度监控系统设计

起重机械作为重要的搬运设备,其安全可靠运行意义重大.针对起重机械控制柜环境温度的需求,分析了各种工况下最不利的环境因素,针对恶劣工况的特殊需求,研究了各种温度传感器的特性和优缺点,选择DS18B20作为温度传感器,搭配STC12C5A08S系列打片机,设计了相关的电路,编写了控制代码,完成了温度监控下位机;上位机程序采用开发测量或控制系统的最常用的图形化开发环境LabWindows/CVI编写.最终形成了一套简单实用的起重机械控制柜温度监控系统,实现在起重机械使用过程中对控制柜进行实时环境温度监控,并在温度漂移出预设温度值时发出警报,为起重机安全运行提供保障.     

Perovskite ceramic oxide as an efficient electrocatalyst for nitrogen fixation

The electrochemical conversion of N₂ to NH₃ is an interesting research topic as it provided an alternative and energy-saving method compared with the traditional way of NH₃ production. Although different materials have been proposed for N₂ reduction, the use of defects in oxides was only reported recently and the relevant working mechanism was not fully revealed. In this study, Sr was used as the dopant for LaFeO₃ to create oxygen vacancies, forming the Sr-doped LFO (La_0.5Sr_0.5FeO_3-δ) perovskite oxide. The La_0.5Sr_0.5FeO_3-δ ceramic oxide used as a catalyst achieves an NH₃ yield of 11.51 μgh^?1 mg^?1 and the desirable faradic efficiency (F.E.) of 0.54% at ?0.6 V vs reversible hydrogen electrode (RHE), which surpassed that of LaFeO₃ nanoparticles. The ¹⁵N isotope labeling method was employed to prove the La_0.5Sr_0.5FeO_3-δ catalyst had the function of converting N₂ into NH₃ under the electrolysis condition. The first principle calculations were used to investigate the mechanism at the atomistic level, revealing that the free energy barriers changed significantly with the introduction of oxygen vacancies that accelerated the overall nitrogen reduction reaction (NRR) procedure.     

水平磁系高梯度磁选机精矿管堵塞原因分析与改造

南京梅山选矿厂针对水平磁系高梯度磁选机在现场使用中暴露出的精矿管堵塞的问题，通过测量水平磁系高梯度磁选机不同位置的漏磁场强度，对磁系的漏磁场分布特性进行研究。研究得出，精矿管堵塞为漏磁场导致，从力场计算结果得出，磁系漏磁产生的最大磁场力可使粒度大于0.3 mm的磁铁矿颗粒在精矿管中发生沉积。     

Ten complementary measures to assist with environmental watering programs in the Murray–Darling river system,Australia

Restoration programmes for degraded aquatic ecosystems frequently focus on flow restoration or reinstatement, including recovery targets for volumes of water to be used for environmental benefit. Australia's Murray–Darling Basin is an example of a major system undergoing substantial water reform to balance the needs of competing users, including the environment, within the constraints of an arid climate. This reform revolves around accounting for finite volumes of water that have been shared amongst water users. We argue that while recovering water will provide good outcomes, as a sole intervention, it is not enough to deliver the desired environmental benefits of the reform given the significantly altered state of the catchment. Here, we present 10 measures that could be used to complement planned water recovery actions. These “complementary measures” integrate recovery actions, which when strategically combined with water delivery would significantly enhance water reform efforts to generate environmental outcomes in a highly modified system.     

Solution-Processed Organic Solar Cells with High Open-Circuit Voltage of 1.3 V and Low Non-Radiative Voltage Loss of 0.16 V

Compared with inorganic or perovskite solar cells, the relatively large non-radiative recombination voltage losses (ΔV_non-rad) in organic solar cells (OSCs) limit the improvement of the open-circuit voltage (V_oc). Herein, OSCs are fabricated by adopting two pairs of D–π–A polymers (PBT1-C/PBT1-C-2Cl and PBDB-T/PBDB-T-2Cl) as electron donors and a wide-bandgap molecule BTA3 as the electron acceptor. In these blends, a charge-transfer state energy (E_CT) as high as 1.70–1.76 eV is achieved, leading to small energetic differences between the singlet excited states and charge-transfer states (ΔE_CT ≈ 0.1 eV). In addition, after introducing chlorine atoms into the π-bridge or the side chain of benzodithiophene (BDT) unit, electroluminescence external quantum efficiencies as high as 1.9 × 10⁻³ and 1.0 × 10⁻³ are realized in OSCs based on PBTI-C-2Cl and PBDB-T-2Cl, respectively. Their corresponding ΔV_non-rad are 0.16 and 0.17 V, which are lower than those of OSCs based on the analog polymers without a chlorine atom (0.21 and 0.24 V for PBT1-C and PBDB-T, respectively), resulting in high V_oc of 1.3 V. The ΔV_non-rad of 0.16 V and V_oc of 1.3 V achieved in PBT1-C-2Cl:BTA3 OSCs are thought to represent the best values for solution-processed OSCs reported in the literature so far.